Nearly all computer speaker ports are color coded. These colors will help you determine which plug goes where. Most speaker cables will be color coded to match these jacks. Place your speakers. Make sure that you can identify the Right and Left channel cables.
If you are setting up a full-surround system, place your surround speakers to the sides and behind your computer chair, angled towards the chair. If you are just setting up two speakers, placing them to the sides of your monitor angled towards you will result in good sound quality. Connect the satellites and center channel to the subwoofer if necessary. Different speaker models will connect to each other in different ways.
Sometimes, you will need to connect the satellite speakers to the subwoofer which then plugs into the computer, while other times each set of speakers gets plugged into the computer separately.
Plug the speakers into the appropriate jacks. Match the speaker cable plug colors to the matching colored jacks on your computer. You may have to twist the plugs if space is tight. Test the speakers. Power on the speakers if necessary and then turn them all the way down using the physical volume control.
Start a song or video on your computer and slowly raise the volume until you can hear at a comfortable level. Once you've confirmed that the speakers work, find a channel test online.
This will help you ensure that your speakers are placed correctly. Method 3. Determine which speakers your stereo supports. Speakers draw power, and some stereos may not be able to handle too much extra draw. Refer to your stereo's documentation when installing new speakers, especially if you are adding additional speakers or replacing existing speakers with high-power replacements. Make sure the speakers will fit. Some speakers are designed to fit into existing speaker locations, while other will require modifications such as cutting away the panel or installing mounting brackets.
Take all of this into consideration when choosing speakers to install. Gather your tools. The tools you need will vary wildly from car to car. The location of the speaker you are installing will also have an impact on the tools you need. In general, however, you will probably need the following: [3] X Research source A variety of screwdrivers. Phillips, flat head, offset, and more. Disconnect the battery. Before working on anything electrical in your car, it is always recommended that you disconnect the power.
Locate your battery and find the appropriate socket wrench that fits the lug on the battery terminals. Disconnect negative black terminal and move the cable gently to the side.
See this guide for detailed instructions on disconnecting a car battery. Read the included instructions. There are too many different possibilities to be covered effectively in this guide. For specific instructions for your speakers, refer to the included documentation or look up the manual on the manufacturer's website. Always defer to the manufacturer's instructions. Remove the speaker grille. These can usually be pried off, though there may be screws to remove. If you are doing this on the front of the dash under the windshield, you may need an offset screwdriver.
Remove the old speaker. Speakers are usually screwed into the panel, so remove all the screws before trying to pull the speaker out.
Take care not to rip out the wiring harness that is usually present. The speaker may be glued to the enclosure, so you may have to pry it off. Unclip the speaker from the wiring harness after removing it from the panel.
You will be plugging your new speaker into this harness. If there is no harness, you will need to cut the wires. Cut holes if necessary. Sometimes the speaker you are inserting will not fit exactly into the existing enclosure.
If this is the case, use your drill to cut out enough space for the speaker. Make sure to measure the new speaker and mark the enclosure so that you don't cut away too much. Wire the new speaker. Most speakers simply clip into the existing wiring harness. If you don't have a wiring harness, you will need to solder the new speaker to the existing speaker wire. Make sure that the positive and negative wires are properly connected. The positive terminal on the back of the speaker is usually larger than the negative one.
Avoid using electrical tape to hold bare wire together, as it will likely warp and lead to a bad connection down the road. Test the speaker. Before mounting the speaker, reconnect your car battery and then test the speaker. Make sure that the sound coming out isn't distorted, and that the speaker is visibly moving at higher volumes. You'll want to ensure that it is properly wired before you finish the mounting process. Mount the speaker. After confirming that the speaker is working properly, mount the speaker using any included mounting brackets and screws.
You may want to use an adhesive to help keep it in place. Adam Nordquist. Speakers connect to computers with the 3. You can find a whole bunch on Amazon. Yes No. Not Helpful 1 Helpful 1. You don't want to run a house speaker in your car.
The house speaker can take more wattage than a car speaker, causing it not to work without an amp. Not Helpful 0 Helpful 0. Include your email address to get a message when this question is answered. If you can temporarily fasten, or hold the speakers in position, you may be able to judge their effectiveness before permanently mounting them.
Helpful 0 Not Helpful 0. Use the shortest wire recommended by the speaker maker, for the length of run you are working with. Longer distances between the speaker and stereo may require larger wire, as will higher wattage components. Submit a Tip All tip submissions are carefully reviewed before being published. You Might Also Like How to. How to. Co-authors: Updated: September 3, Categories: Audio Speakers. Bahasa Indonesia: Memasang Pengeras Suara. Since many desktop computers don't have built-in sound output, external speakers and headphones can be essential for listening to audio on your device.
If you are having trouble connecting these peripherals to your computer, review the sections below for help. On most portable speakers, the right-channel speaker is the "main" speaker with the volume knob , and it often has two or more wires coming out of the back. One of these wires should connect to the left speaker, and another should have a 3. If your speakers require a power source to amplify the audio, there should also be a power cord.
This cord needs to connect to a wall outlet or surge protector outlet. On the back of the computer, connect the mini plug to the audio line-level output. This port is usually colored lime green , as shown in the picture. Some motherboards may also have the following connections not pictured for 4, 5. The device should be automatically recognized by the computer.
For additional information, consult the user manual for your device.
0コメント